| | 1 | # Enviro+ |
| | 2 | |
| | 3 | Designed for environmental monitoring, Enviro+ lets you measure air quality (pollutant gases and particulates), temperature, pressure, humidity, light, and noise level. Learn more - https://shop.pimoroni.com/products/enviro-plus |
| | 4 | |
| | 5 | |
| | 6 | [](https://travis-ci.com/pimoroni/enviroplus-python) |
| | 7 | [](https://coveralls.io/github/pimoroni/enviroplus-python?branch=master) |
| | 8 | [](https://pypi.python.org/pypi/enviroplus) |
| | 9 | [](https://pypi.python.org/pypi/enviroplus) |
| | 10 | |
| | 11 | # Installing |
| | 12 | |
| | 13 | You're best using the "One-line" install method if you want all of the UART serial configuration for the PMS5003 particulate matter sensor to run automatically. |
| | 14 | |
| | 15 | **Note** The code in this repository supports both the Enviro+ and Enviro Mini boards. _The Enviro Mini board does not have the Gas sensor or the breakout for the PM sensor._ |
| | 16 | |
| | 17 |  |
| | 18 |  |
| | 19 | |
| | 20 | ## One-line (Installs from GitHub) |
| | 21 | |
| | 22 | ``` |
| | 23 | curl -sSL https://get.pimoroni.com/enviroplus | bash |
| | 24 | ``` |
| | 25 | |
| | 26 | **Note** report issues with one-line installer here: https://github.com/pimoroni/get |
| | 27 | |
| | 28 | ## Or... Install and configure dependencies from GitHub: |
| | 29 | |
| | 30 | * `git clone https://github.com/pimoroni/enviroplus-python` |
| | 31 | * `cd enviroplus-python` |
| | 32 | * `sudo ./install.sh` |
| | 33 | |
| | 34 | **Note** Raspbian Lite users may first need to install git: `sudo apt install git` |
| | 35 | |
| | 36 | ## Or... Install from PyPi and configure manually: |
| | 37 | |
| | 38 | * Run `sudo pip install enviroplus` |
| | 39 | |
| | 40 | **Note** this wont perform any of the required configuration changes on your Pi, you may additionally need to: |
| | 41 | |
| | 42 | * Enable i2c: `raspi-config nonint do_i2c 0` |
| | 43 | * Enable SPI: `raspi-config nonint do_spi 0` |
| | 44 | |
| | 45 | And if you're using a PMS5003 sensor you will need to: |
| | 46 | |
| | 47 | * Enable serial: `raspi-config nonint set_config_var enable_uart 1 /boot/config.txt` |
| | 48 | * Disable serial terminal: `sudo raspi-config nonint do_serial 1` |
| | 49 | * Add `dtoverlay=pi3-miniuart-bt` to your `/boot/config.txt` |
| | 50 | |
| | 51 | And install additional dependencies: |
| | 52 | |
| | 53 | ``` |
| | 54 | sudo apt install python-numpy python-smbus python-pil python-setuptools |
| | 55 | ``` |
| | 56 | |
| | 57 | ## Help & Support |
| | 58 | |
| | 59 | * GPIO Pinout - https://pinout.xyz/pinout/enviro_plus |
| | 60 | * Support forums - http://forums.pimoroni.com/c/support |
| | 61 | * Discord - https://discord.gg/hr93ByC |
projects / EVA-2020-02-2.git / blame_incremental